You're new here! Welcome, please feel free to browse our store.

KK MultiCopter Control Board - Blackboard V5.5




KK MultiCopter Control Board - Blackboard V5.5
Code MULTIBoard1
Our Price: £19.97
Quantity:
Standard Price: £34.99
You Save: £15.02
% Saved: 42.93%

Select Product Options

Choose Configuration:
DUALCopter
H6Copter
HEXCopter
QUADCopter
TRICopter
TWINCopter
XCopter
Y4Copter
Y6Copter

Description

WARNING - These are NOT Plug and Play MultiCopter Controller Boards - 
NO EMAIL OR PHONE SUPPORT WILL BE GIVEN !!!!

We do however supply full written instructions and a video to allow you to follow all the setting up procedure - 
PLEASE FOLLOW THEM TO THE LETTER, or you will encounter configeration and setting up problems !

PLEASE READ CAREFULLY
These Boards are only suitable for flyers with previous experience or technically minded . . . !  !
You will be required to do a certain amount of setting up and configuration to enable these boards to function and operate correctly, 
you may need to re-flash the board with other firmware than that supplied to allow it to work with your R/C gear or make other adjustments for this board to operate correctly.

Should you not feel confident or have no experience of these types of boards, or can can ask someone who may help you locally, we suggest you first do some on line research to establish if these boards are boyond your capabilites - Again these board are NOT plug and play - 
Please do not purchase if you are not happy with the above statement !

This is the Ultimate KK MultiCopter Control Board V5.5 . . .for Tri-copters, Quad-copters and upto six Motors



What is a Multi-Copter Control board ?

 

This KKMulticopter controller is a flight control board for up to 6 Rotor Aircraft. Its purpose is to stabilise the aircraft during flight. To do this it takes the signal from the three on board gyros (roll, pitch and yaw) then passes the signal to the Atmega168PA IC. The Atmega168PA IC unit then processes these signals according the users installed software and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabalises your Quadcopter.

These control boards also use signals from your radio systems receiver (Rx) and passes these signals to the Atmega8PA IC via the ail (aileron), ele (elevator), thr (throttle) and rud (rudder) inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).

This is the latest v.5.5 KKmulticontroller that has been factory made and fully populated. It uses the Murata piezoelectric gyros which have been incorporated into the board design for robustness. The Yaw gyro assembly is also slot mounted for extra robustness. These gyros have proven to be the most vibration resistant of all the gyros we have tested so far.

The board comes in black with a blue LED and has an on board In System Programming (ISP) header to enable easy firmware updates with a recommended programmer. The on board Atmega168PA chip gives users the extra space to load expanded firmware with higher refresh rates to enhance stability.

The three adjustable potentiometers increase or decrease gyro gain for all three axis (Roll, Pitch and Yaw) and can be used to calibrate the ESCs and reverse the gyro directions if necessary during pre-flight setup.

The board also has six ESC/Servo headers which allow multicopter configurations from 2 to 6 rotors. There are also headers for the aileron, elevator, throttle and rudder connections from your RC Receiver(RX). The board comes with a 4 x 3 pin jumper cables to connect your RX to the board quickly and easily.


Note. . . . .
this is not supplied in kit form
It is fully assembled and works straight out of the box. Can be used to control the main
controls of a 2 to 6 motor model by means of the built in Gyros. See SPECIAL NOTE BELOW

Earlier kit versions required the builder to also purchase suitable Gyros
, strip out the electronics and re-assemble on the main board, this one has everything done for you, and will maintain stability on any TRI or QUAD copter of your choice !

SEE our Range of Suitable MULTI-COPTERS Click here

Specifications

Size: 50.5mm x 50.5mm x 23.5mm
Weight: 14.5 gram
IC: Atmega168PA
Gyro: Murata piezoelectric gyros
Input Voltage: 3.3-5.5V
Signal from Receiver: 1520us (4 channels)
Signal to ESC: 1520us (6 ESCs)

SPECIAL NOTE


  1. These boards are supplied to control upto 6 motors, the firmware is what makes it work correctly, so please select the one you want from the above choices.
  2. For a small charge, we can change the firmware to either the Tricopter or Quadcopter version at a later date should you wish to transfer it into another model.
These boards are supplied to control 2 to 6 motors, the main control chip Atmega168PA IC, needs to be programmed for a particular function, so please select the correct setup from the options at the top of this page for the type of model you want to control . . . Should you wish to change the firmware yourself at any time, we highly recommend you also get the Firmware Loader / USB programmer - the USB Programmer is available here














Choice of Firmware (installed at time of purchase for FREE)


SingleCopter
TwinCopter
Dualcopter
Tri-Copter
Quadcopter (X or + Configuration)
X-Copter
Y4-copter
Hexa-copter
SexyCopter (Hexacopter)
Y6 Copter
H6-Copter
X6-Copter
PowerTower Osprey Firmware - 2 Rotors
VTOL
AeroPlane
KKPlus Bootloader

TERMS OF SALE & DISCLAIMER - 
 
By purchasing this item, you are in aggreement that Pyramid Models or the owners, cannot give any support, will not be held 
responsible for any crash damage to this Circuit Board or other connected R/C gear, however caused or even a collision or crash by inexperience pilots, and under no circumstances will a claim for exchange or refund be accepted once used.

This board is an open circuit and should be treated with respect,  all Boards are thouroughly checked and tested before dispatch and incorrect wiring or setting up may result in your aircraft becoming unstable and a crash occurring, this may cause serious damage to the board, yourself, nearby objects, and any other radio gear connected to this board.

 

 

Customer Reviews (view all)

Average Rating 5

ranjit jeganathan, Rated: 5

KK Multicopter 5.5

bought from here to control a new build tricopter with 450mm booms came pre-programmed with v2.3 firmware. with spectrum dx6i needs throttle normal, aileron reversed, elevator reversed, rudder reversed, gyro normal and pitch reversed. In heil mode with 90 degree single servo. Expos at 30% all other settings left as is. with balanced props and good centre of gravity lifts up with pots at 50% in a stable and controlled manner - mine that is.
follow David WindestŚl's Rcexplorer set-up guide to set motor balance direction ect.


Review this product...

Related Products:

This Quadcopter frame provides the perfect test bed or starting point for any Quadcopter enthusiast.
Our Price: £29.95

This is a Fully assembled Tricopter or Quadcopter Control Board for Enthusiastic Builders
Our Price: £29.95

KK2.0 MultiCopter and HK Control Board - Firmware Loader/Programmer
Our Price: £14.99

KK MultiCopter Power/ESC Board V2
Our Price: £4.99

MWC MultiWii SE Standard Edition 4-axis Flight Control Board QUADX with FTDI Basic Breakout
Our Price: £63.56

People who purchased this also purchased...

KK2.0 MultiCopter and HK Control Board - Firmware Loader/Programmer
Our Price: £14.99

KK Multicopter Flight Control Board Guard / Protecter - Tricopter - Quadcopter - Hexacopter
Our Price: £6.99

KK MultiCopter Power/ESC Board V2
Our Price: £4.99

This Quadcopter frame provides the perfect test bed or starting point for any Quadcopter enthusiast.
Our Price: £29.95

This is a Fully assembled Tricopter or Quadcopter Control Board for Enthusiastic Builders
Our Price: £29.95