You're new here! Welcome, please feel free to browse our store.

KK MultiCopter Power/ESC Board V2




KK MultiCopter Power/ESC Board V2
Code PowerBoard2
Our Price: £4.99
Quantity:
Standard Price: £8.99
You Save: £4.00
% Saved: 44.49%

Select Product Options

Description

This is the Power Board V2 for direct compatibility with the KK MultiCopter Control Board V5.5 or the HobbyKing KK Board V2 . . .for Tri-copters, Quad-copters and upto six/eight Motors -the mounting holes match those of a Multicopter Board for simultaneous vertical mounting

The V2 Board is capable of connecting multiple power connections for up to 8 motors as well as compatibility with a I2C ESC see description below for the KK Multicopter Control Board V5.5
 

 

What is a Multi-Copter Control board ?

This KKMulticopter controller is a flight control board for up to 6 Rotor Aircraft. Its purpose is to stabilise the aircraft during flight. To do this it takes the signal from the three on board gyros (roll, pitch and yaw) then passes the signal to the Atmega168PA IC. The Atmega168PA IC unit then processes these signals according the users installed software and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabalises your multicopter such as a Quadcopter.

These control boards also use signals from your radio systems receiver (Rx) and passes these signals to the Atmega168PA IC via the ail (aileron), ele (elevator), thr (throttle) and rud (rudder) inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).

This is the latest v.5.5 KKmulticontroller that has been factory made and fully populated. It uses the Murata piezoelectric gyros which have been incorporated into the board design for robustness. The Yaw gyro assembly is also slot mounted for extra robustness. These gyros have proven to be the most vibration resistant of all the gyros we have tested so far.

The board comes in black with a blue LED and has an on board In System Programming (ISP) header to enable easy firmware updates with a recommended programmer. The on board Atmega168PA chip gives users the extra space to load expanded firmware with higher refresh rates to enhance stability.

The three adjustable potentiometers increase or decrease gyro gain for all three axis (Roll, Pitch and Yaw) and can be used to calibrate the ESCs and reverse the gyro directions if necessary during pre-flight setup.

The board also has six ESC/Servo headers which allow multicopter configurations from 2 to 6 rotors. There are also headers for the aileron, elevator, throttle and rudder connections from your RC Receiver(RX). The board comes with a 4 x 3 pin jumper cables to connect your RX to the board quickly and easily.


Note. . . . . 
this is not supplied in kit form
It is fully assembled and works straight out of the box. Can be used to control the main
controls of a 2 to 6 motor model by means of the built in Gyros. See SPECIAL NOTE BELOW 

Earlier kit versions required the builder to also purchase suitable Gyros
, strip out the electronics and re-assemble on the main board, this one has everything done for you, and will maintain stability on any TRI or QUAD copter of your choice !

SEE our Range of Suitable MULTI-COPTERS Click here

Specifications

Size: 50.5mm x 50.5mm x 23.5mm
Weight: 14.5 gram
IC: Atmega168PA
Gyro: Murata piezoelectric gyros
Input Voltage: 3.3-5.5V
Signal from Receiver: 1520us (4 channels)
Signal to ESC: 1520us (6 ESCs)

SPECIAL NOTE


  1. These boards are supplied to control upto 6 motors, the firmware is what makes it work correctly, so please select the one you want from the above choices.
  2. For a small charge, we can change the firmware to either the Tricopter or Quadcopter version at a later date should you wish to transfer it into another model.
These boards are supplied to control 2 to 6 motors, the main control chip Atmega48PA IC, needs to be programmed for a particular function, so please select the correct setup from the options at the top of this page for the type of model you want to control . . . Should you wish to change the firmware yourself at any time, we highly recommend you also get the Firmware Loader / USB programmer - the USB Programmer is available here














 

 

Customer Reviews

There are currently no reviews for this product. Be the first to review by clicking below!


Review this product...

Related Products:

This Quadcopter frame provides the perfect test bed or starting point for any Quadcopter enthusiast.
Our Price: £29.95

This is a Fully assembled Tricopter or Quadcopter Control Board for Enthusiastic Builders
Our Price: £29.95

KK2.0 MultiCopter and HK Control Board - Firmware Loader/Programmer
Our Price: £14.99

This is the ultimate KK MultiCopter Control Board for Tri-copters Quads upto six Motors
Our Price: £19.97

Special Offer
QUADCopter XR100
Our Price: £9.99

This Quadcopter frame provides the perfect test bed or starting point for any Quadcopter enthusiast.
Our Price: £74.95

This is a Fully assembled Multicopter Control Board for Enthusiastic Builders controling upto six motors
Our Price: £32.99


KK MultiCopter & HK Board Power/ESC Board V6 for up to 8 motors - Octocopters
Our Price: £12.99

People who purchased this also purchased...

KK Multicopter Flight Control Board Guard / Protecter - Tricopter - Quadcopter - Hexacopter
Our Price: £6.99

This is the ultimate KK MultiCopter Control Board for Tri-copters Quads upto six Motors
Our Price: £19.97


This Quadcopter frame provides the perfect test bed or starting point for any Quadcopter enthusiast.
Our Price: £29.95

HK TALON Quadcopter Frame
Our Price: £47.00